391 lines
12 KiB
Python
Executable File
391 lines
12 KiB
Python
Executable File
#!/bin/env python3
|
|
from sys import exit
|
|
from time import sleep
|
|
from RPi.GPIO import IN, OUT
|
|
import RPi.GPIO as GPIO
|
|
from re import fullmatch
|
|
import argparse
|
|
import atexit
|
|
# EEPROM AT28C256 Pin names and RPi GPIO Pin Numbers
|
|
# b means bar = inverted
|
|
|
|
|
|
gpio_l = [2, 3, 4, 17, 27, 22, 10, 9, 11, 5, 6, 13, 19, 26]
|
|
gpio_r = [14, 15, 18, 23, 24, 25, 8, 7, 12, 16, 20, 21]
|
|
#
|
|
# Defining which 6502 pin goes to which GPIO pin
|
|
#
|
|
|
|
A = [
|
|
# 27, 22, 10, 9, 11, 5, 6, 13,
|
|
13, 6, 5, 11, 9, 10, 22, 27, # A0 - A7
|
|
2, 3, 17, 4, # A8 - A11
|
|
23, 18, 15 # A12 - A14
|
|
]
|
|
|
|
# IO = gpio_r[4:12] # 8 io pins
|
|
# IO.reverse()
|
|
IO = [ 24, 25, 8, 7, 12, 16, 20, 21 ]
|
|
|
|
OEb = 26 # Output Enable
|
|
WEb = 19 # Write Enable
|
|
CEb = 14 # Chip Enable is hooked up to A15 on the processor
|
|
|
|
controls = [CEb, WEb, OEb]
|
|
|
|
# TIMES
|
|
# Read:
|
|
t_ACC = 150 * 1e-9 # Address to Output Delay
|
|
|
|
# Write:
|
|
t_AS = 0 # Address Setup time
|
|
t_AH = 50 * 1e-9 # Address Hold Time
|
|
t_CS = 0 # Chip Select Hold Time
|
|
t_WP = 100 * 1e-9 # Write Pulse Width
|
|
t_DS = 50 * 1e-9 # Data Setup Time_CS = 0
|
|
t_DH = 0 # Data Hold Time
|
|
t_WPH = 50 * 1e-9 # Write Puls High
|
|
t_WPH = 50 * 1e-4 # Write Pulse High !!!2*e5 longer than in Datasheet, since shorter high caused Problems with my Chip!!!
|
|
|
|
PRINT_HEX = True
|
|
PRINT_BIN = False
|
|
PRINT_DEC = False
|
|
REP_CHAR = '\n'
|
|
|
|
|
|
|
|
#
|
|
# UTILITY
|
|
#
|
|
def print_pins():
|
|
for i in range(len(A)):
|
|
print(f" A{i:02} - {A[i]}")
|
|
for i in range(len(IO)):
|
|
print(f"IO{i:02} - {IO[i]}")
|
|
print(f" CEb - {CEb}")
|
|
print(f" WEb - {WEb}")
|
|
print(f" OEb - {OEb}")
|
|
|
|
|
|
def format_number(n, hex_digits=2, bin_digits=8, dec_digits=3, sep=" "):
|
|
s = ""
|
|
if not PRINT_HEX and not PRINT_BIN and not PRINT_DEC:
|
|
print("ERROR: echo: at least one of hex, bin, dec must be set to True")
|
|
exit(1)
|
|
if PRINT_HEX: s += "0x" + format(n, f'0{hex_digits}x') + sep
|
|
if PRINT_BIN: s += "0b" + format(n, f'0{bin_digits}b') + sep
|
|
if PRINT_DEC: s += format(n, f'0{dec_digits}') + sep
|
|
return s[:-len(sep)]
|
|
|
|
|
|
def echo(address: int, value: int, message: str="", mode: str="-", end=None):
|
|
"""
|
|
print a message for a given address and value
|
|
"""
|
|
s = mode + " " "[" + format_number(address, hex_digits=4, bin_digits=15, dec_digits=5) \
|
|
+ "] {" + format_number(value, hex_digits=2, bin_digits=8, dec_digits=3) + "} " \
|
|
+ message
|
|
print(s, end=REP_CHAR if end is None else end)
|
|
|
|
|
|
def clear_line():
|
|
print(" " * 80, end='\r')
|
|
|
|
|
|
def convert_to_int(v):
|
|
"""
|
|
convert 0xABC and 0b0101 to int
|
|
"""
|
|
if type(v) == str and fullmatch(f"0x[0-9,a-f,A-F]+", v):
|
|
return int(v.replace("0x", ""), 16)
|
|
elif type(v) == str and fullmatch(f"0b[0]+", v):
|
|
return int(v.replace("0b", ""), 2)
|
|
return int(v)
|
|
|
|
|
|
def get_n_bits(i: int):
|
|
"""
|
|
return how many bits are needed to express the number in binary
|
|
"""
|
|
return len(bin(i)) - 2 # -2 for the "0x"
|
|
|
|
|
|
def get_bit(value: int, n: int):
|
|
"""
|
|
get the n-th bit (0-based)
|
|
"""
|
|
return value & (1 << n)
|
|
|
|
|
|
def read_binary_file(filepath, from_ad=0) -> list[int]:
|
|
with open(filepath, "rb") as file:
|
|
bindata = []
|
|
for byte in file.read():
|
|
bindata.append(byte)
|
|
return bindata[from_ad:]
|
|
|
|
|
|
|
|
#
|
|
# GPIO functions
|
|
#
|
|
def setup_io_pins(IOdirection=OUT):
|
|
# OUT when writing and IN when reading
|
|
for pin in IO:
|
|
GPIO.setup(pin, IOdirection)
|
|
|
|
def setup_pins():
|
|
# setup the pins
|
|
GPIO.setmode(GPIO.BCM)
|
|
for pin in controls:
|
|
GPIO.setup(pin, OUT, initial=1) # inverted, is 1 means disable
|
|
for pin in A:
|
|
GPIO.setup(pin, OUT, initial=0)
|
|
setup_io_pins(IN)
|
|
|
|
|
|
|
|
|
|
def cleanup():
|
|
GPIO.cleanup()
|
|
|
|
|
|
def set_address(address: int, bits=15):
|
|
"""
|
|
set the address pins to the given value
|
|
"""
|
|
for j in range(bits):
|
|
GPIO.output(A[j], get_bit(address, j))
|
|
|
|
|
|
def write_byte(byte: int, address: int, verbose=True, debug=False):
|
|
if verbose: echo(address, byte, mode="w")
|
|
|
|
GPIO.output(OEb, 1)
|
|
# setup the address
|
|
set_address(address, bits=15)
|
|
setup_io_pins(OUT)
|
|
# Setup Data
|
|
for j in range(8):
|
|
GPIO.output(IO[j], get_bit(byte, j))
|
|
# wait "Address" Setup Time
|
|
sleep(t_AS)
|
|
# wait "Data Setup Time"
|
|
sleep(t_DS)
|
|
|
|
GPIO.output(CEb, 0)
|
|
# Start the write pulse -> enable WEb
|
|
GPIO.output(WEb, 0)
|
|
|
|
# wait until minimum write pulse width is reached. in theory, should be t_WP-t_DS but this caused problems
|
|
sleep(t_WP)
|
|
|
|
if debug:
|
|
clear_line()
|
|
echo(address, byte, mode="w", message="DEBUG: Press enter to continue")
|
|
input()
|
|
|
|
|
|
# End Write Pulse -> disable WEb
|
|
GPIO.output(WEb, 1)
|
|
GPIO.output(CEb, 1)
|
|
|
|
# wait "Data Hold"
|
|
sleep(t_DH)
|
|
|
|
GPIO.output(CEb, 0)
|
|
GPIO.cleanup(IO)
|
|
setup_io_pins(IN)
|
|
|
|
# check the toggle bit IO6, if it stops toggling the write is done
|
|
timeout = 0
|
|
while timeout < 1e3:
|
|
GPIO.output(OEb, 0)
|
|
sleep(1e-9)
|
|
bit1 = GPIO.input(IO[6])
|
|
GPIO.output(OEb, 1)
|
|
sleep(1e-9)
|
|
GPIO.output(OEb, 0)
|
|
sleep(1e-9)
|
|
bit2 = GPIO.input(IO[6])
|
|
GPIO.output(OEb, 1)
|
|
sleep(1e-9)
|
|
if bit1 == bit2:
|
|
timeout = 1e3
|
|
timeout += 1
|
|
GPIO.output(CEb, 1)
|
|
|
|
|
|
def read_byte(address: int, verbose=True, debug=False) -> int:
|
|
GPIO.output(WEb, 1)
|
|
setup_io_pins(IN)
|
|
# set the address valid
|
|
ad_bin = set_address(address, bits=15)
|
|
|
|
# low in chip/output enable -> enable
|
|
GPIO.output(CEb, 0)
|
|
GPIO.output(OEb, 0)
|
|
|
|
# wait the "Address to Output Delay" until the output is valid
|
|
sleep(t_ACC)
|
|
|
|
|
|
byte = 0
|
|
for j in range(8):
|
|
byte |= (GPIO.input(IO[j]) << j)
|
|
|
|
if debug:
|
|
clear_line()
|
|
echo(address, byte, mode="r", message="DEBUG: Press enter to continue")
|
|
input()
|
|
|
|
# high in OEb and CEb -> disable
|
|
GPIO.output(OEb, 1)
|
|
GPIO.output(CEb, 1)
|
|
|
|
if verbose: echo(address, byte, mode="r")
|
|
|
|
return byte
|
|
|
|
|
|
#
|
|
# FUNCTIONS
|
|
#
|
|
def read(from_ad=0, to_ad=255, delay=1e-3, ignore=[0xff], debug=False, compare:list[int]=[], verbose=True) -> list[int]:
|
|
"""
|
|
from_ad: start address from where to read
|
|
to_ad: end address to read to
|
|
delay: delay between readings in s
|
|
verbose: wether to print the reading
|
|
ignore: list of values which are not printed
|
|
"""
|
|
content = []
|
|
unequal = []
|
|
|
|
for i in range(from_ad, to_ad + 1):
|
|
byte = read_byte(i, verbose=verbose, debug=debug)
|
|
content.append(byte)
|
|
|
|
if compare:
|
|
if not compare[i-from_ad] == byte:
|
|
unequal.append(i)
|
|
echo(i, byte, "vs {" + format_number(compare[i-from_ad], hex_digits=2, bin_digits=8, dec_digits=3) + "} in file", mode="c", end="\n")
|
|
|
|
# wait artifical delay
|
|
sleep(delay)
|
|
clear_line()
|
|
if compare:
|
|
return unequal
|
|
return content
|
|
|
|
|
|
def write(content: list[int], from_ad=0, delay=0, debug=False, only_diff=True, verbose=True, check_written=True):
|
|
"""
|
|
Write a list if bytes to the eeprom.
|
|
WEb controlled
|
|
"""
|
|
to_ad = from_ad+len(content)-1
|
|
current_content = []
|
|
if only_diff:
|
|
print(f"Reading EEPROM and only writing deviating values")
|
|
current_content = read(from_ad, to_ad=to_ad, delay=delay, debug=debug, verbose=True)
|
|
assert len(content) == len(current_content)
|
|
failed = []
|
|
print(f"Writing to EEPROM: {len(content)} bytes from address {format(from_ad, '04x')} to {format(to_ad, '04x')}.")
|
|
|
|
for i in range(len(content)):
|
|
if not only_diff or (only_diff and content[i] != current_content[i]):
|
|
write_byte(content[i], from_ad + i, verbose=True, debug=debug)
|
|
# wait artifical delay
|
|
sleep(delay)
|
|
clear_line()
|
|
print("Write to EEPROM - Done!")
|
|
if check_written:
|
|
print("Comparing EEPROM to file...")
|
|
failed = read(from_ad=from_ad, to_ad=to_ad, delay=delay, debug=debug, verbose=False, compare=content)
|
|
retries = 1
|
|
while len(failed) > 0 and retries > 0:
|
|
print(f"Found {len(failed)} bytes deviating from the file - retrying: {retries} times")
|
|
for ad in failed:
|
|
write_byte(content[ad-from_ad], ad, verbose=verbose)
|
|
failed = read(from_ad=from_ad, to_ad=to_ad, delay=delay, debug=debug, verbose=False, compare=content)
|
|
retries -= 1
|
|
clear_line()
|
|
print("Comparing complete")
|
|
if len(failed) > 0:
|
|
print(f"Errors occured: {len(failed)} values could not be written:")
|
|
print("[", end="")
|
|
for ad in failed:
|
|
print(format(ad, '04x'), end=",")
|
|
print("]")
|
|
return
|
|
|
|
|
|
def erase(from_ad=0, to_ad=32767, **keys):
|
|
"""
|
|
Write all 1 to the EEPROM
|
|
WEb controlled
|
|
"""
|
|
data = [0xff for i in range(from_ad, to_ad)]
|
|
write(data, from_ad=from_ad, **keys)
|
|
print("Erased EEPROM - Done!")
|
|
return
|
|
|
|
|
|
def main():
|
|
global REP_CHAR, PRINT_BIN, PRINT_DEC, PRINT_HEX
|
|
parser = argparse.ArgumentParser(
|
|
prog="AT28C256-EEPROM Writer",
|
|
description="Read and write from/to an AT28C256 EEPROM via the Raspberry Pi 4's GPIO pins\n2023 Matthias Quintern",
|
|
epilog="Numbers can be passed as int, hex prefixed with '0x' and binary prefixed with '0b'",
|
|
)
|
|
parser.add_argument("--write", "-w", dest="write", action="store_true", default=False, help="write binary file onto the EEPROM")
|
|
parser.add_argument("--compare", "-c", dest="compare", action="store_true", default=False, help="compare EEPROM content to binary file")
|
|
parser.add_argument("--read", "-r", dest="read", action="store_true", default=False, help="read the contents of the EEPROM")
|
|
parser.add_argument("--erase", "-e", dest="erase", action="store_true", default=False, help="erase the contents of the EEPROM")
|
|
parser.add_argument("--file", "-f", metavar="file", dest="file", action="store", default="", help="file for --write and --compare")
|
|
parser.add_argument("--from", metavar="start-address", dest="from_ad", action="store", default=0, type=convert_to_int, help="start at address x")
|
|
parser.add_argument("--to", metavar="end-address", dest="to_ad", action="store", default=0x7fff, type=convert_to_int, help="end at address y (inclusive)")
|
|
parser.add_argument("--debug", dest="debug", action="store_true", default=False, help="stop the program after setting up the address")
|
|
parser.add_argument("--delay", dest="delay", metavar="delay", action="store", type=float, default=0.0, help="extra delay between cycles")
|
|
parser.add_argument("--ignore", dest="ignore", metavar="numbers", action="store", nargs="*", type=convert_to_int, default=[0x100], help="ignore the numbers a b ... Default=[0xff]")
|
|
parser.add_argument("--verbose", "-v", dest="verbose", action="store_true", default=False, help="increase verbosity")
|
|
parser.add_argument("--print-pins", dest="print_pins", action="store_true", default=False, help="print the pin layout and exit")
|
|
parser.add_argument("--no-hex", dest="no_hex", action="store_true", default=False, help="Dont print values hex")
|
|
parser.add_argument("--bin", dest="bin", action="store_true", default=False, help="Print values in binary")
|
|
|
|
args = parser.parse_args()
|
|
|
|
if (args.write or args.compare) and not args.file:
|
|
parser.error('--file is required with --write and --compare')
|
|
|
|
if not args.verbose: REP_CHAR = '\r'
|
|
if args.no_hex: PRINT_HEX = False
|
|
if args.bin: PRINT_BIN = True
|
|
|
|
if args.print_pins:
|
|
print_pins()
|
|
exit(0)
|
|
if args.erase:
|
|
erase(from_ad=args.from_ad, to_ad=args.to_ad, delay=args.delay, debug=args.debug, verbose=args.verbose)
|
|
if args.write:
|
|
write(read_binary_file(args.file, from_ad=args.from_ad), from_ad=args.from_ad, delay=args.delay, debug=args.debug, verbose=args.verbose)
|
|
if args.read:
|
|
read(from_ad=args.from_ad, to_ad=args.to_ad, delay=args.delay, debug=args.debug, verbose=args.verbose, ignore=args.ignore)
|
|
if args.compare:
|
|
unequal = read(from_ad=args.from_ad, to_ad=args.to_ad, delay=args.delay, debug=args.debug, verbose=args.verbose, ignore=args.ignore, compare=read_binary_file(args.file))
|
|
print(f"Found {len(unequal)} deviating values")
|
|
|
|
|
|
if __name__ == '__main__':
|
|
atexit.register(cleanup)
|
|
setup_pins()
|
|
main()
|
|
|
|
# PRINT_BIN = True
|
|
# for i in range(15):
|
|
# address = (1 << i)
|
|
# PRINT_BIN = True
|
|
# set_address(address=address)
|
|
# input(f"DEBUG: {format_number(address, hex_digits=4, bin_digits=15)}")
|